Metal Architecture Home

Metal Roofing

Standing Seam Roof Systems - May 2016

Standing seam roof systems featured in Metal Architecture's May 2016 issue.

All Weather Insulated Panels

All Weather Insulated Panels

All Weather Insulated Panels' SR2 Standing Seam Roof Panels feature 26-gauge G-90 galvanized steel surfaces with standard PVDF and SMP exterior coatings. Trapezoidal ribs provide strength for foot traffic and hidden fastener joinery provides weather protection. SR2 Standing Seam Roof Panels have the appearance of traditional standing seam with the benefits of insulated metal panels. Optional factory caulked seams are available.

www.awipanels.com

McElroy Metal

McElroy Metal

McElroy Metal's Meridian standing seam metal roof system is installed by placing pancake head fasteners in the panels' slotted flanges. They are attached to the roof deck with pancake head fasteners and clips are not needed. The snap-together system may be installed on slopes greater than 3:12. Seams 1-inch tall are recommended for residential and commercial applications over solid decking.

www.mcelroymetal.com

Englert Inc.

Englert Inc.

Englert's Series A1300 metal roof panels are a 1 1/2-inch mechanically seamed metal roof system. The profile features architectural detailing, tight radius curving and narrow, snap-lock seams. A1300 has the detailing of snap-lock metal roof panels and is used on shallow sloped metal roofs less than 3:12. Additionally, A1300 may be used for fascias, walls and soffits. It is successfully tested for UL 580, Class 90, Florida Building Code compliance, ASTM water and air, ASTM E-84 (Class A Fire Rating) and ASTM E-1592.

www.englertinc.com

Metl-Span

Metl-Span

Metl-Span's CFR insulated metal standing seam metal roof panel with a 2-inch-high standing seam are installed from the top side with concealed clips and fasteners placed in the side joints. They feature factory-cut panel ends, factory notching and factory-swaged ends that reduce field reworking and erection cost. Additionally, factory-installed backer plates at the end-laps make pre-drilling for special fasteners and fastener tools unnecessary.

www.metlspan.com/products/cfr-roof-systems

Green Span Profiles

Green Span Profiles

Green Span Profiles' RidgeLine 2 3/8-inch-tall mechanically seamed metal roof panels slide together without rolling or lifting to engage side-laps. The panels feature shoulder fasteners to prevent over-driving, continuous weathertight seal at the side-laps and factory-applied sealant in the batten caps. RidgeLine panels may be used on slopes as low as 1/2:12. They are available 2.5, 3, 4 or 5 inches thick. They provide R-8 per inch of insulation thickness; 2.5-inch panels have R-20 per inch of insulation thickness.

www.greenspanprofiles.com

Petersen Aluminum Corp.

Petersen Aluminum Corp.

Petersen Aluminum's PAC-150 Single Lock standing seam metal roof panels have a 1 1/2-inch seam height and are mechanically field seamed to 90 degrees or 180 degrees depending on uplift requirements. The panels may be installed on a variety of substrates and on slopes as low as 1/2:12. PAC-150 have concealed fastener clips, are available in steel and aluminum and in 12-inch to 20-inch widths. Floating clips are available to reduce expansion and contraction. An optional sealant bead may be applied for additional weather resistance.

www.pac-clad.com

MBCI

MBCI

MBCI's LokSeam standing seam metal roof system combines the aesthetics of an architectural panel and the strength of a structural panel. They are available 12, 16 and 18 inches wide and can be installed over open framing or a solid substructure. LokSeam panels can transition from roof to fascia with a rib cover and is offered in a variety of colors.

www.mbci.com

Varco Pruden Buildings

Varco Pruden Buildings

Varco Pruden Buildings' SSR System is a low-slope, clip-mounted standing seam roof interlocked and mechanically field-seamed into place, yielding a single membrane. A slotted clip allows thermal movement to 3 1/4 inches. SSR System is available in standard 24-gauge and optional 22-gauge. Finish options include unpainted Galvalume and 14 KXL Cool Colors.

www.vp.com